+44 (0)24 7671 8970
More publications     •     Advertise with us     •     Contact us
 
Loading...
{megaLeaderboard}
{normalLeaderboard}
News Article

Tandem solar cell achieves 26 percent peak efficiency

Perovskite/BN sandwich absorbs most of visible light spectrum

Scientists at the University of California, Berkeley, and Lawrence Berkeley National Laboratory have reported a new perovskite photovoltaic device design that achieves an average steady-state efficiency of 18.4 percent, with a high of 21.7 percent and a peak efficiency of 26 percent. The results are published in the journal Nature Materials.

"We have set the record now for different parameters of perovskite solar cells, including the efficiency," said senior author Alex Zettl, a UC Berkeley professor of physics, senior faculty member at Berkeley Lab and member of the Kavli Energy Nanosciences Institute. "The efficiency is higher than any other perovskite cell - 21.7 percent - which is a phenomenal number, considering we are at the beginning of optimising this."

"This has a great potential to be the cheapest photovoltaic on the market, plugging into any home solar system," said Onur Ergen, the lead author of the paper and a UC Berkeley physics graduate student.

The achievement comes thanks to a new way to combine two perovskite solar cell materials - each tuned to absorb a different wavelength or colour of sunlight - into one "˜graded bandgap' solar cell that absorbs nearly the entire spectrum of visible light. Previous attempts to merge two perovskite materials have failed because the materials degrade one another's electronic performance.

"This is realising a graded bandgap solar cell in a relatively easy-to-control and easy-to-manipulate system," Zettl said. "The nice thing about this is that it combines two very valuable features - the graded bandgap, a known approach, with perovskite, a relatively new but known material with surprisingly high efficiencies - to get the best of both worlds."

Full-spectrum solar cells

Like all semiconductors, perovskite materials only conduct electricity only if the electrons can absorb enough energy - from a photon of light, for example - to kick them over a forbidden energy gap or bandgap. These materials preferentially absorb light at specific energies or wavelengths - the bandgap energy - but inefficiently at other wavelengths.

"In this case, we are swiping the entire solar spectrum from infrared through the entire visible spectrum," Ergen said. "Our theoretical efficiency calculations should be much, much higher and easier to reach than for single-bandgap solar cells because we can maximise coverage of the solar spectrum."

The key to mating the two materials into a tandem solar cell is a single-atom thick layer of hexagonal BN, which looks like a layer of chicken wire separating the perovskite layers from one other.

In this case, the perovskite materials are made of the organic molecules methyl and ammonia, but one contains the metals tin and iodine, while the other contains lead and iodine doped with bromine. The former is tuned to preferentially absorb light with an energy of 1 electron volt (eV) - infrared, or heat energy - while the latter absorbs photons of energy 2 eV, or an amber colour.

The monolayer of BN allows the two perovskite materials to work together and make electricity from light across the whole range of colours between 1 and 2 eV.

The perovskite/BN sandwich is placed on a lightweight aerogel of graphene that promotes the growth of finer-grained perovskite crystals, serves as a moisture barrier and helps stabilise charge transport though the solar cell, Zettl said. Moisture makes perovskite fall apart.

The whole thing is capped at the bottom with a gold electrode and at the top by a GaN layer that collects the electrons that are generated within the cell. The active layer of the thin-film solar cell is about 400 nanometers thick.

"Our architecture is a bit like building a quality automobile roadway," Zettl said. "The graphene aerogel acts like the firm, crushed rock bottom layer or foundation, the two perovskite layers are like finer gravel and sand layers deposited on top of that, with the hexagonal BN layer acting like a thin-sheet membrane between the gravel and sand that keeps the sand from diffusing into or mixing too much with the finer gravel. The GaN layer serves as the top asphalt layer."

It is possible to add even more layers of perovskite separated by hexagonal BN, though this may not be necessary, given the broad-spectrum efficiency they've already obtained, the researchers said.

"People have had this idea of easy-to-make, roll-to-roll photovoltaics, where you pull plastic off a roll, spray on the solar material, and roll it back up," Zettl said. "With this new material, we are in the regime of roll-to-roll mass production; it's really almost like spray painting."

Schletter Group: 48 MWp Project in Italy
ENCAVIS Acquires Two More Solar Parks In Spain and Surpasses The Planned Expansion
Maximum profitability with KACO advanced technology for complex solar roofs
Enviromena wins contract to re-power three major solar farms ahead of the summer energy peak
New Swansea University Collaboration to Support Sustainable, Locally Manufactured Solar PV
New Swansea University Collaboration to Support Sustainable, Locally Manufactured Solar PV
Next2Sun Builds World's Largest Vertical PV Plant at Frankfurt Airport
DNV Publishes Bankability Study of Solcast Satellite Irradiance Data
Steel company SSAB switches to fossil-free energy in Italy with PV solution from Solnet
janom Investments enters the Croatian solar energy industry by investing in a 30 MW power plant project
Trina Solar Vertex S+ 505W n-type dual-glass modules enter mass production
BayWa r.e. and 3E sign partnership agreement for monitoring & analytics of global PV portfolio
Accelerating Spain's Energy Transformation: LONGi to supply Naturgy with 1 million modules in new deal
NTR announces corporate PPA with Almac Group to buy energy from Murley Wind Farm, Northern Ireland
Oxford PV sets new solar panel efficiency world record
Order Intake for the Construction of Wind Turbines in Turkey
Trilantic Europe acquires stake in AEROCOMPACT Group
Octopus Energy makes solar farm debut in Germany
Austria-based KOGA Energy, a solar EPC solutions provider, has kicked off.
Exus to acquire 625MW New Mexico solar portfolio
Capcora Accompanies SUSI Partners In Raising Senior Debt For a Polish Renewables Portfolio
Qualitas Energy acquires a 96 MW wind energy project pipeline in Germany
Nordex Group receives orders from the UK for approx. 150 MW
Trina Solar gains EPD certification from UL Solutions and EPDItaly for industry leading modules
Mandarin Oriental Hyde Park, London instals innovative solar tech to decarbonise heating
Efficiency First: The Road to Electrification
SCHLETTER Supplies Austria's Largest PV Roof System
E.ON partners with UK renewable heat innovator Naked Energy
Sonnedix signs innovative EUR500 million loan facility to finance construction of its renewable electricity pipeline in Europe and UK
Construction begins on Glennmont and Ørsted’s Borkum Riffgrund 3 offshore wind farm in Germany
ABB shores up reliable power supply at Southeast Asia’s largest floating solar plant
Sonnedix starts construction of 300MW UK solar PV portfolio

×
Search the news archive

To close this popup you can press escape or click the close icon.
Logo
×
Logo
×
Register - Step 1

You may choose to subscribe to the Solar + Power Magazine, the Solar + Power Newsletter, or both. You may also request additional information if required, before submitting your application.


Please subscribe me to:

 

You chose the industry type of "Other"

Please enter the industry that you work in:
Please enter the industry that you work in: